Sorry to say I don't have an H loom handy - it's at the back n beyond of my store room or I could have laid it out and shown you.
For some reason the manual doesn't show the Pink wire but I guess it would then make it too easy to come up with a bypass for it.
I am sure there is a thread somewhere telling you what size of resistor to connect to what pin of the CDI to fool the speed circuit.
MM!
Bike won't rev past 9 half rpm
Moderator: Moderators
- Mori Man
- Blingmeister
- Posts: 1976
- Joined: Thu May 10, 2007 3:30 pm
- My Bike: ZXR400J2
- Location: JAPAN
Re: Bike won't rev past 9 half rpm
Nothing worse than having an H and not being able to scratch it !
Living life on the edge, SuPposedly
Living life on the edge, SuPposedly
-
- Posts: 88
- Joined: Sun Oct 22, 2006 5:16 pm
- My Bike: ZXR400 L4
- Location: Congleton
Re: Bike won't rev past 9 half rpm
Just read through this topic, and its got me wondering, i am building a track bike and have had my loom converted to a race loom my track electronics i think it was, it is connected to a uk CDI, will it be in failsafe mode as i have no speedo?
- Mori Man
- Blingmeister
- Posts: 1976
- Joined: Thu May 10, 2007 3:30 pm
- My Bike: ZXR400J2
- Location: JAPAN
Re: Bike won't rev past 9 half rpm
Your all right Dolts , UK CDI has no speed restriction circuit in it.
Nothing worse than having an H and not being able to scratch it !
Living life on the edge, SuPposedly
Living life on the edge, SuPposedly
-
- Posts: 13
- Joined: Mon Nov 14, 2011 8:12 am
- My Bike: ZXR400 + R1
Re: Bike won't rev past 9 half rpm
Developments
There is a pink wire on the CDI. I get the resistor to ground mod, this will take place this week and will report back.
The number on the CDI is not one I have seen on the forum. Red label, 21119-1271, 131800-5240, 12v TNCF07 A is a Denso unit. Any info on this fella's?
There is a pink wire on the CDI. I get the resistor to ground mod, this will take place this week and will report back.
The number on the CDI is not one I have seen on the forum. Red label, 21119-1271, 131800-5240, 12v TNCF07 A is a Denso unit. Any info on this fella's?
- Mori Man
- Blingmeister
- Posts: 1976
- Joined: Thu May 10, 2007 3:30 pm
- My Bike: ZXR400J2
- Location: JAPAN
Re: Bike won't rev past 9 half rpm
H1 / J1 CDItechnicalmoto wrote:
The number on the CDI is not one I have seen on the forum. Red label, 21119-1271, 131800-5240, 12v TNCF07 A is a Denso unit. Any info on this fella's?
Nothing worse than having an H and not being able to scratch it !
Living life on the edge, SuPposedly
Living life on the edge, SuPposedly
-
- Posts: 13
- Joined: Mon Nov 14, 2011 8:12 am
- My Bike: ZXR400 + R1
Re: Bike won't rev past 9 half rpm
Thanks
I did a little more digging and as you confirm its a Japan spec cdi with the speed limiter. I will fit resistor to overcome this.
Gotta say this forum is a fantastic resource for the ZXR.......
I did look at programmable CDI's for £165 but the resistor is deffo cheaper.
I did a little more digging and as you confirm its a Japan spec cdi with the speed limiter. I will fit resistor to overcome this.
Gotta say this forum is a fantastic resource for the ZXR.......
I did look at programmable CDI's for £165 but the resistor is deffo cheaper.