Hi folks,
Hope this is the right part of the forum - I'm a newbie here. I took delivery of my 400 yesterday - it's a L 1992 model, 20000 miles and in really good nick and running order. The only issue I can see (apart from the carbs needing setting properly) at the moment is a poor join in the seat farings - they don't join in the middle that well and the previous owner solved it with some black tape which looks nasty. I'm new to this bike so sorry if this is a stupid question but what, if anything, is usually used on this join? Cheers in advance for any advice! Jez
Seat fairing fitting on an L2
Moderator: Moderators
- masterofinsanity
- Site Admin
- Posts: 8111
- Joined: Thu Aug 29, 2002 12:36 am
- My Bike: Aprilia Tuono Fighter
- Location: England
- Contact:
Re: Seat fairing fitting on an L2
they should join mate, take both seat pads off, there should be 3 screws keeping them together, if they won't join then the subframe may be bent?
Don't forget people there is more to the zxr400 than this forum... check out www.zxrworld.co.uk also.
-
- Posts: 6
- Joined: Tue Oct 14, 2008 4:27 pm
- My Bike: ZXR400
Re: Seat fairing fitting on an L2
Thanks for quick reply, I'll have to investigate it later - hope it just some missing screws or broken lugs and not the subframe! Cheers, Jez
-
- L-plate hell
- Posts: 330
- Joined: Sat Aug 09, 2008 11:49 pm
- My Bike: L1 racer
Re: Seat fairing fitting on an L2
If its just the rear section of the subframe thats twisted i have one here, make me an offer.
-
- zxr400 oc member
- Posts: 613
- Joined: Sun Oct 21, 2007 12:24 pm
- My Bike: zx7r p6
- Location: Stafford
Re: Seat fairing fitting on an L2
undo all the bolts holding the panels onto the frame then join the two halves together. try and refit and if the holes wont line up then the frame is bent.
-
- Posts: 6
- Joined: Tue Oct 14, 2008 4:27 pm
- My Bike: ZXR400
Re: Seat fairing fitting on an L2
Cheers guys, I will try that later. Will, I will let you know if it is the subframe and make an offer if I need it. Thanks again, Jez
- masterofinsanity
- Site Admin
- Posts: 8111
- Joined: Thu Aug 29, 2002 12:36 am
- My Bike: Aprilia Tuono Fighter
- Location: England
- Contact:
Re: Seat fairing fitting on an L2
there should be 2 bolts holding the plastics underneath the rear seat pad, these are probably missing too. or have rusted in, heads snapped off and the plastics are catching on the broken stubs which is why there may be a gap.
Don't forget people there is more to the zxr400 than this forum... check out www.zxrworld.co.uk also.
- RedexRobB
- Site Admin
- Posts: 7212
- Joined: Fri Aug 30, 2002 7:37 pm
- My Bike: ZXR400L3
- Location: Ipswich, Suffolk
Re: Seat fairing fitting on an L2
anyone considered they might be cheap plastics?
-
- Posts: 6
- Joined: Tue Oct 14, 2008 4:27 pm
- My Bike: ZXR400
Re: Seat fairing fitting on an L2
Thanks guys - I'll have a look at the bolts as well. You could be right as well Redex, they might be replacement plastics although they are ij the right colours. If they are nastys can anyone recommend a good make for replacements (I'm not going for anything on ebay from China - they all look well dodgy). Cheers. Jez
- masterofinsanity
- Site Admin
- Posts: 8111
- Joined: Thu Aug 29, 2002 12:36 am
- My Bike: Aprilia Tuono Fighter
- Location: England
- Contact:
Re: Seat fairing fitting on an L2
there's usually loads on ebay, i've got some green ones.
Don't forget people there is more to the zxr400 than this forum... check out www.zxrworld.co.uk also.