Fitting Undertray?

MillaMeter · Post by **MillaMeter** » Thu Mar 13, 2008 7:56 pm

Hi,

I bought a Ermax Undertray for my ZXR400.

Looking at the intructions, they're not very clear at all. Does anyone know how these fit to the bike? I mean do I need to cut, drill etc...? or does the undertray just hang on the side panels?

Thanks,

Richard

Post by **Northern ANdy** » Thu Mar 13, 2008 9:31 pm

just hangs basically. I added some brackets to mine though, mainly so the undertray stays put without the side panels.

MillaMeter · Post by **MillaMeter** » Fri Mar 14, 2008 1:23 am

Northern ANdy wrote:just hangs basically. I added some brackets to mine though, mainly so the undertray stays put without the side panels.

Oh right, any chance you could maybe show me what brackets you used and how you fitted them and where? sorry for the stupid questions, I really am crap at improvising

Thanks.

Richard

MillaMeter · Post by **MillaMeter** » Fri Mar 14, 2008 6:48 pm

Well, I managed to fit the undertray today which I must say was a complete giraffe to fit! although it's just sitting there hanging, it really is a very nice snug fit.

Here's the turn out after frustration hours working on it.

Post by **masterofinsanity** » Sat Mar 15, 2008 4:08 am

thats a bit clean aint it? looking very nice mate!

MillaMeter · Post by **MillaMeter** » Sat Mar 15, 2008 6:55 am

Hehe thanx

Scott221 · Post by **Scott221** » Sat Mar 15, 2008 12:23 pm

Tempted....

Post by **Northern ANdy** » Sat Mar 15, 2008 5:56 pm

I just bent up some steel sheet in the vice, drilled the tray to 5mm, and the brackets go upto some M8 tapped holes in the subframe which where there for something else, but I forget what.

MillaMeter · Post by **MillaMeter** » Sat Mar 15, 2008 6:28 pm

Northern ANdy wrote:I just bent up some steel sheet in the vice, drilled the tray to 5mm, and the brackets go upto some M8 tapped holes in the subframe which where there for something else, but I forget what.

The rear grab handles underneath maybe?

RedexRobB · Post by **RedexRobB** » Sun Mar 16, 2008 12:37 am

pillion footpegs?

Post by **M14nydMoo** » Sun Mar 16, 2008 12:36 pm

Looks really good, I've been looking around at a few. Where did you get yours from and how much, if you don't mind me asking.

MillaMeter · Post by **MillaMeter** » Sun Mar 16, 2008 6:57 pm

M14nydMoo wrote:Looks really good, I've been looking around at a few. Where did you get yours from and how much, if you don't mind me asking.

wot can get them from a website called intobikes.co.uk for Â£110

Post by **Northern ANdy** » Sun Mar 16, 2008 7:01 pm

got mine direct from ermax

Post by **Vard66** » Sat May 17, 2008 2:51 am

... plus flared lights... with... the hoods... sprayed... black..... gnnnnnnnnnn.... I need... money.... to.... make bike... look.... the nuts....

www.zxrworld.co.uk

Fitting Undertray?

Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?

Re: Fitting Undertray?